# Uplift resistance

How Rischio checks piles pulled up: each pile's load under a moment on the cap, a single pile's side resistance, and a group as its piles or as one block.

A pile is pulled up when the load on the cap points up, an uplift, or when a moment on a group’s cap lifts its outer piles. AASHTO checks the uplift resistance of a single pile (10.7.3.10) and of a group (10.7.3.11), and sends drilled shafts to the same articles (10.8.3.7.2 and 10.8.3.7.3). Units, symbols and assumptions are set out in [Method and assumptions](https://rischio.io/docs/deep-foundation/theory/).

## Each pile’s load

The cap is rigid. With a moment on it, it loads its piles unequally, each by its position $x, y$ from the group’s centre:

$$
P = \frac{V}{n} + \frac{M_x\, x}{\Sigma x^2} + \frac{M_y\, y}{\Sigma y^2}
$$

(AASHTO C10.7.3.10; FHWA GEC 12, Eq. 8-79). The most loaded pile is checked against one pile’s capacity, $\mathrm{FS} = Q_u/P_{max}$ (10.7.3.8: “factored axial compression resistance of a single pile”), and the least loaded, if its load is negative, is pulled. The plan view draws each pile’s load.

## A single pile

“The nominal uplift resistance of a single pile should be estimated in a manner similar to that for estimating the side resistance of piles in compression” (10.7.3.10): $R_s$, the pile’s own [shaft resistance](https://rischio.io/docs/deep-foundation/theory/shaft/), the one its capacity takes. It’s checked against the pull on the most pulled pile, $T$: a single pile under an upward load, or a group’s pile lifted by its cap.

$$
\mathrm{FS} = \frac{R_s}{T}
$$

In free mode, UFS 3-220-20’s 3.0 for piles in tension sits beside it as a reference (Table 6-29). Under [AASHTO LRFD](https://rischio.io/docs/reference/aashto-lrfd/), $R_R = \phi_{up} R_s$, each stratum’s side with its own $\phi_{up}$: for a driven pile by its side’s method, 0.35 for Nordlund’s in sand and 0.25 for the α-method in clay (Table 10.5.5.2.3-1), already 80 % of the factor in compression (C10.7.3.10); for a drilled shaft by the soil, 0.35 in clay, 0.45 in sand and 0.40 in rock (Table 10.5.5.2.4-1). At an extreme event it’s 0.80 (10.5.5.3.2, 10.5.5.3.3). The combination that pulls most governs, with the dead load at its least, 0.90.

## A group

Under a net upward load $V_{up}$, the group’s uplift resistance is the lesser of its piles’ sum, $n R_s$, and the group lifted as one block (10.7.3.11):

-   **where the piles cross a clay**, the block $X \times Y$ of the group’s plan, $Z$ deep from the cap to the toe, by the undrained strength along its sides and its weight (Eq. 10.7.3.11-2, Fig. 10.7.3.11-2), with $\bar{S}_u$ the average along the sides, a sand’s taken as 0;
-   **in cohesionless soil**, the weight of the soil a spread of 1H in 4V lifts, from the toe up to the cap (Fig. 10.7.3.11-1, after Tomlinson).

$$
R_{ug} = (2XZ + 2YZ)\,\bar{S}_u + W_g \;\;\text{where the piles cross a clay}, \qquad R_{ug} = W_g \;\;\text{in cohesionless soil}
$$

$W_g$ takes the soil’s effective weight, buoyant below the water table, and counts the piles inside the block as soil (FHWA GEC 12, §7.2.3.2.2). The cap’s own weight is in the load’s dead part, so it isn’t added again. Each piece of the block, cut where $\gamma'$ changes, weighs its prismoidal volume, exact for a block with plane sides. Into rock, AASHTO writes no block: the sum of the piles governs. Each of these is said in the uplift check’s trace ([What a check supposes](https://rischio.io/docs/deep-foundation/warnings/#what-a-check-supposes)).

$$
\mathrm{FS} = \frac{R_{ug}}{V_{up}}
$$

In free mode, 3.0 beside it as a reference. Under AASHTO, the piles’ sum takes their $\phi_{up}$ and the block $\phi_{ug}$, 0.50 for driven piles and 0.45 for drilled shafts (Tables 10.5.5.2.3-1 and 10.5.5.2.4-1, Eq. 10.7.3.11-1), 0.80 at an extreme event.

## References

-   AASHTO (2024). *LRFD Bridge Design Specifications*, 10th ed. A single pile’s uplift and a group’s (10.7.3.10, 10.7.3.11, 10.8.3.7.2 and 10.8.3.7.3) and their resistance factors (Tables 10.5.5.2.3-1 and 10.5.5.2.4-1).
-   Hannigan, P. J., Rausche, F., Likins, G. E., Robinson, B. R., & Becker, M. L. (2016). *Design and Construction of Driven Pile Foundations*, Vol. I, FHWA-NHI-16-009 (GEC 12). Federal Highway Administration.
-   Tomlinson, M. J. (1987). *Pile Design and Construction Practice*, 3rd ed. Viewpoint Publications.
-   U.S. Department of Defense (2026). *Foundations*, UFS 3-220-20. Unified Facilities Criteria.

---

Source: https://rischio.io/docs/deep-foundation/theory/uplift/
