# Equations

Every step of Rischio's retaining wall calculation, with its equation, in the same order as the calculation report.

These are the same steps, in the same order, as the calculation report; a report leaves out what its model doesn’t have, such as uplift without water.

## 1Geometry and weights

1.  Weight of each part
    
    $$
    W = A \cdot \gamma_c
    $$
    
    where $A$ area of each part (m²)
    
2.  Weight of the soil on the wall
    
    $\gamma_{sat}$ below the water table
    
    $$
    W_s = \Sigma A_i \gamma_i
    $$
    
3.  Weight of each part
    
    $\gamma+n\gamma_w$ below the water table
    
    $$
    W = A \cdot \gamma
    $$
    
    where $A$ area of each part (m²)
    

## 2Earth pressure

1.  Height of the back
    
    Height of the wall's back, from the heel to the crest
    
    $$
    H'
    $$
    
2.  Inclination of the wall's back
    
    The plane from the heel to the crest's back corner
    
    $$
    \theta = \tan^{-1}\frac{x_{heel} - x_{crest}}{H'}
    $$
    
    where $H'$ height of the back (m)
    
3.  Active pressure coefficient, in each stratum
    
    Coulomb
    
    $$
    K_a = \frac{\cos^2(\phi' - \theta)}{\cos^2\theta \cos(\delta' + \theta)\left[1 + \sqrt{\frac{\sin(\phi' + \delta')\sin(\phi' - \alpha)}{\cos(\delta' + \theta)\cos(\theta - \alpha)}}\right]^2}
    $$
    
    where $\theta$ inclination of the wall's back (°)
    
4.  Wall friction, in each stratum
    
    $$
    \delta' = (\delta'/\phi')\, \phi'
    $$
    
5.  Surcharge
    
    $$
    q_s = \Sigma q_i
    $$
    
6.  Thrust of the surcharge
    
    From the crest's back $q_s$ lies on the active wedge, its weight reaching the wall only through this thrust
    
    $$
    \Delta P_{a,h} \approx K_a \, q_s \, H'
    $$
    
    where $q_s$ surcharge (kPa); $H'$ height of the back (m)
    
7.  Active thrust, horizontal
    
    A gravity wall's back: the Rankine wedge from the heel meets the wall, so Coulomb on the wall's own back, the plane from the heel to the crest's back corner, at the wall friction δ′, the soil inside it as wall weight (AASHTO LRFD 10th, Fig. C3.11.5.3-1b, left)
    
    $$
    P_{a,h} = \int_0^{H'} \left(\sigma'_v + q_s \frac{\cos\theta}{\cos(\theta - \alpha)}\right) K_a \, dz \cdot \cos(\theta + \delta')
    $$
    
    where $q_s$ surcharge (kPa); $H'$ height of the back (m); $\theta$ inclination of the wall's back (°)
    
8.  Active thrust, vertical
    
    $$
    P_{a,v} = \int_0^{H'} \sigma_a \, dz \cdot \sin(\theta + \delta')
    $$
    
9.  Water thrust
    
    $$
    P_w = \tfrac{1}{2} \gamma_w h_w^2
    $$
    

## 3Uplift pressure

1.  Uplift pressure at the heel
    
    $$
    u_{heel} = \gamma_w h_{heel}
    $$
    
2.  Uplift pressure at the toe
    
    $$
    u_{toe} = \gamma_w h_{toe}
    $$
    
3.  Uplift force
    
    $$
    U = \tfrac{1}{2} (u_{heel} + u_{toe}) B
    $$
    
    where $u_{heel}$ uplift pressure at the heel (kPa); $u_{toe}$ uplift pressure at the toe (kPa); $B$ base width (m)
    
4.  Lever arm of the uplift force
    
    $$
    x_U = \frac{B (u_{toe} + 2 u_{heel})}{3 (u_{toe} + u_{heel})}
    $$
    
    where $u_{heel}$ uplift pressure at the heel (kPa); $u_{toe}$ uplift pressure at the toe (kPa)
    

## 4Sliding

1.  Total horizontal force
    
    $$
    \Sigma H = P_{a,h} + P_w
    $$
    
    where $P_{a,h}$ active thrust, horizontal (kN/m); $P_w$ water thrust (kN/m)
    
2.  Shear resistance under the base
    
    Cast on cohesionless soil, C = 1.0 (Eq. 10.6.3.4-2); free mode takes it without φτ (AASHTO 11.6.3.6)
    
    $$
    R_\tau = \Sigma V \tan \phi_f
    $$
    
    where $\Sigma V$ total vertical force (kN/m); $B$ base width (m)
    
3.  Resistance to sliding
    
    The passive in front neglected (AASHTO 11.6.3.5 allows it)
    
    $$
    R = R_\tau
    $$
    
    where $R_\tau$ shear resistance under the base (kN/m)
    
4.  Sliding
    
    $$
    FS = \frac{R}{\Sigma H}
    $$
    

## 5Eccentricity

1.  Resisting moment
    
    $$
    \Sigma M_R = \Sigma W_i x_i + W_s x_s + P_{a,v} x_a
    $$
    
    where $W$ weight of each part (kN/m); $x$ lever arm of each part (m); $W_s$ weight of the soil on the wall (kN/m); $x_s$ lever arm of each stratum (m); $P_{a,v}$ active thrust, vertical (kN/m); $x_a$ where the vertical part of the active thrust meets the back (m)
    
2.  Overturning moment
    
    $$
    \Sigma M_O = P_{a,h} \, y_a + P_w \, y_w + U x_U
    $$
    
    where $P_{a,h}$ active thrust, horizontal (kN/m); $y_a$ height of the horizontal part of the active thrust (m); $P_w$ water thrust (kN/m); $y_w$ height of the water thrust (m); $U$ uplift force (kN/m); $x_U$ lever arm of the uplift force (m)
    
3.  Total vertical force
    
    $$
    \Sigma V = \Sigma W_i + W_s + P_{a,v} - U
    $$
    
    where $W$ weight of each part (kN/m); $W_s$ weight of the soil on the wall (kN/m); $P_{a,v}$ active thrust, vertical (kN/m); $U$ uplift force (kN/m)
    
4.  Eccentricity of the resultant
    
    $$
    e = \left| \frac{B}{2} - \frac{\Sigma M_R - \Sigma M_O}{\Sigma V} \right|
    $$
    
    where $B$ base width (m); $\Sigma M_R$ resisting moment (kN·m/m); $\Sigma M_O$ overturning moment (kN·m/m); $\Sigma V$ total vertical force (kN/m)
    
5.  Eccentricity
    
    $$
    e \le \frac{B}{6}
    $$
    

## 6Bearing capacity

1.  Maximum contact pressure
    
    $$
    q_{max} = \frac{\Sigma V}{B} \left(1 + \frac{6e}{B}\right)
    $$
    
    where $\Sigma V$ total vertical force (kN/m); $B$ base width (m); $e$ eccentricity of the resultant (m)
    
2.  Minimum contact pressure
    
    $$
    q_{min} = \frac{\Sigma V}{B} \left(1 - \frac{6e}{B}\right)
    $$
    
    where $\Sigma V$ total vertical force (kN/m); $B$ base width (m); $e$ eccentricity of the resultant (m)
    
3.  Effective width
    
    $$
    B' = B - 2e
    $$
    
    where $B$ base width (m); $e$ eccentricity of the resultant (m)
    
4.  Overburden at the base
    
    $$
    q = \sigma'_v(D_f)
    $$
    
5.  Unit weight above the base
    
    Total (moist) unit weight above the base, by thickness, taken below the water table too, as 10.6.3.1.2a defines it, with $C_{wq}$ for the water: a submerged soil's effective unit weight is about half its dry one (AASHTO LRFD 10th ed., C10.6.3.1.1)
    
    $$
    \gamma_q
    $$
    
6.  Unit weight below the base
    
    Total (moist) unit weight of the stratum the base rests on, taken below the water table too, as 10.6.3.1.2a defines it, with $C_{w\gamma}$ for the water: a submerged soil's effective unit weight is about half its dry one (AASHTO LRFD 10th ed., C10.6.3.1.1)
    
    $$
    \gamma_f
    $$
    
7.  Cohesion term
    
    $$
    c N_c s_c i_c
    $$
    
    where $c$ cohesion of the soil under the base (kPa); $N_c$ bearing capacity factor; $s_c$ shape factor; $i_c$ inclination factor
    
8.  Surcharge term
    
    $$
    \gamma_q D_f N_q s_q d_q i_q C_{wq}
    $$
    
    where $\gamma_q$ unit weight above the base (kN/m³); $D_f$ embedment depth (m); $N_q$ bearing capacity factor; $s_q$ shape factor; $d_q$ depth factor; $i_q$ inclination factor; $C_{wq}$ water factor of the surcharge
    
9.  Soil weight term
    
    $$
    \tfrac{1}{2} \gamma_f B' N_\gamma s_\gamma i_\gamma C_{w\gamma}
    $$
    
    where $\gamma_f$ unit weight below the base (kN/m³); $B'$ effective width (m); $N_\gamma$ bearing capacity factor; $s_\gamma$ shape factor; $i_\gamma$ inclination factor; $C_{w\gamma}$ water factor of the soil's weight
    
10.  Ultimate bearing capacity
     
     AASHTO LRFD 10th ed., Eq. 10.6.3.1.2a-1
     
     $$
     q_n = c N_c s_c i_c + \gamma_q D_f N_q s_q d_q i_q C_{wq} + \tfrac{1}{2} \gamma_f B' N_\gamma s_\gamma i_\gamma C_{w\gamma}
     $$
     
     where $T_1$ cohesion term (kPa); $T_2$ surcharge term (kPa); $T_3$ soil weight term (kPa)
     
11.  Equivalent uniform pressure
     
     Meyerhof
     
     $$
     q_{eq} = \frac{V}{B'}
     $$
     
     where $V$ total vertical force (kN/m); $B'$ effective width (m)
     
12.  Bearing capacity
     
     On soil, the equivalent uniform pressure (UFS 3-220-20 §4-5.1.4)
     
     $$
     FS = \frac{q_n}{q_{eq}}
     $$
     

## 7Gabion levels

1.  Resisting moment, from each level up
    
    About the level's toe
    
    $$
    \Sigma M_R
    $$
    
2.  Overturning moment, from each level up
    
    About the level's toe
    
    $$
    \Sigma M_O
    $$
    
3.  Eccentricity of each level on the one below
    
    $$
    e = \left| \frac{B}{2} - \frac{\Sigma M_R - \Sigma M_O}{\Sigma V} \right| \le \frac{B}{6}
    $$
    
4.  Sliding of each level on the one below
    
    $$
    FS \; \ge 1.5
    $$
    

## 8Allowable bearing pressure

1.  Maximum contact pressure
    
    $$
    q_{max} = \frac{\Sigma V}{B} \left(1 + \frac{6e}{B}\right)
    $$
    
    where $\Sigma V$ total vertical force (kN/m); $B$ base width (m); $e$ eccentricity of the resultant (m)
    
2.  Allowable bearing pressure
    
    Given with the base
    
    $$
    q_a
    $$
    
3.  Bearing pressure
    
    The greatest ordinate of the base's linear pressure diagram, at its most loaded edge (its formula as UFC 3-220-20 prints it, Eq. 5-7): the total pressure at the base
    
    $$
    q_{max} \le q_a
    $$

---

Source: https://rischio.io/docs/retaining-wall/equations/
