# Equations

Each equation of Rischio's footing calculation, from the eccentricity to the settlement, with the name and unit of every term.

The same steps, in the same order, as the calculation report.

## 1Loads and geometry

1.  Eccentricity along the width
    
    $$
    e_B = M_B / V
    $$
    
    where $V$ vertical load (kN)
    
2.  Effective width
    
    $$
    B' = \min(B - 2 e_B,\; L - 2 e_L)
    $$
    
    where $B$ width (m); $e_B$ eccentricity along the width (m); $L$ length (m); $e_L$ eccentricity along the length (m)
    
3.  Eccentricity along the length
    
    $$
    e_L = M_L / V
    $$
    
    where $V$ vertical load (kN)
    
4.  Effective length
    
    $$
    L' = \max(B - 2 e_B,\; L - 2 e_L)
    $$
    
    where $B$ width (m); $e_B$ eccentricity along the width (m); $L$ length (m); $e_L$ eccentricity along the length (m)
    
5.  Effective area
    
    $$
    A' = B' L'
    $$
    
    where $B'$ effective width (m); $L'$ effective length (m)
    
6.  Load inclination
    
    $$
    \beta = \arctan(|H| / V)
    $$
    
    where $H$ horizontal load (kN); $V$ vertical load (kN)
    
7.  Effective width
    
    A circle as the square of its area (AASHTO C10.6.1.3)
    
    $$
    B' = D \sqrt{\pi} / 2
    $$
    
    where $D$ diameter (m)
    

## 2Bearing capacity

1.  Overburden at the base
    
    $$
    q = \sigma'_v(D_f)
    $$
    
2.  Effective unit weight below the base
    
    Das & Sivakugan, Eqs. 6.25 to 6.27: the effective unit weight averaged within B below the base
    
    $$
    \gamma = \bar{\gamma}' (D_f \text{ to } D_f + B)
    $$
    
    where $B$ width (m)
    
3.  Effective stress B/2 below the base
    
    $$
    q' = \sigma'_v(D_f + B/2)
    $$
    
4.  Shear modulus of the soil
    
    Of the stratum B/2 below the base
    
    $$
    G_s = \frac{E_s}{2(1 + \mu_s)}
    $$
    
5.  Rigidity index
    
    Vesic, as Das & Sivakugan give it (Eq. 6.43)
    
    $$
    I_r = \frac{G_s}{c' + q' \tan\phi'}
    $$
    
    where $G_s$ shear modulus of the soil (kPa); $q'$ effective stress B/2 below the base (kPa)
    
6.  Critical rigidity index
    
    General shear: $I_r$ is at least $I_{r(cr)}$
    
    $$
    I_{r(cr)} = \tfrac{1}{2}\exp\left[\left(3.30 - 0.45\frac{B}{L}\right)\cot\left(45 - \frac{\phi'}{2}\right)\right]
    $$
    
7.  Bearing capacity factor
    
    Das & Sivakugan, Eq. 6.30, Prandtl
    
    $$
    N_c = (N_q - 1)\cot\phi',\ 5.14 \text{ at } \phi' = 0
    $$
    
8.  Bearing capacity factor
    
    Das & Sivakugan, Eq. 6.29, Reissner
    
    $$
    N_q = \tan^2(45° + \phi'/2)\, e^{\pi \tan\phi'}
    $$
    
9.  Bearing capacity factor
    
    Das & Sivakugan, Eq. 6.31, Vesic
    
    $$
    N_\gamma = 2 (N_q + 1) \tan\phi'
    $$
    
10.  Depth over width
     
     B the base's own, not B′ (Das & Sivakugan, 6.11, Step 2)
     
     $$
     D_f / B
     $$
     
     where $D_f$ embedment depth (m); $B$ width (m)
     
11.  Shape factor
     
     Das & Sivakugan, Table 6.3, De Beer (1970)
     
     $$
     F_{cs} = 1 + \frac{B'}{L'}\frac{N_q}{N_c}
     $$
     
12.  Shape factor
     
     Das & Sivakugan, Table 6.3, De Beer (1970)
     
     $$
     F_{qs} = 1 + \frac{B'}{L'}\tan\phi'
     $$
     
13.  Shape factor
     
     Das & Sivakugan, Table 6.3, De Beer (1970)
     
     $$
     F_{\gamma s} = 1 - 0.4\frac{B'}{L'}
     $$
     
14.  Depth factor
     
     Das & Sivakugan, Table 6.3, Hansen (1970)
     
     $$
     F_{cd} = F_{qd} - \frac{1 - F_{qd}}{N_c \tan\phi'}
     $$
     
     where $D_f/B$ depth over width
     
15.  Depth factor
     
     Das & Sivakugan, Table 6.3, Hansen (1970)
     
     $$
     F_{qd} = 1 + 2\tan\phi' (1 - \sin\phi')^2 \frac{D_f}{B}
     $$
     
     where $D_f/B$ depth over width
     
16.  Depth factor
     
     Das & Sivakugan, Table 6.3, Hansen (1970)
     
     $$
     F_{\gamma d} = 1
     $$
     
17.  Inclination factor
     
     Das & Sivakugan, Table 6.3, Meyerhof (1963); Hanna and Meyerhof (1981)
     
     $$
     F_{ci} = \left(1 - \frac{\beta°}{90°}\right)^2
     $$
     
     where $\beta$ load inclination (°)
     
18.  Inclination factor
     
     Das & Sivakugan, Table 6.3, Meyerhof (1963); Hanna and Meyerhof (1981)
     
     $$
     F_{qi} = \left(1 - \frac{\beta°}{90°}\right)^2
     $$
     
     where $\beta$ load inclination (°)
     
19.  Inclination factor
     
     Das & Sivakugan, Table 6.3, Meyerhof (1963); Hanna and Meyerhof (1981)
     
     $$
     F_{\gamma i} = \left(1 - \frac{\beta°}{\phi'°}\right)^2
     $$
     
     where $\beta$ load inclination (°)
     
20.  Cohesion term
     
     $$
     c' N_c F_{cs} F_{cd} F_{ci}
     $$
     
     where $c'$ cohesion of the soil under the base (kPa); $N_c$ bearing capacity factor; $F_{cs}$ shape factor; $F_{cd}$ depth factor; $F_{ci}$ inclination factor
     
21.  Surcharge term
     
     $$
     q N_q F_{qs} F_{qd} F_{qi}
     $$
     
     where $q$ overburden at the base (kPa); $N_q$ bearing capacity factor; $F_{qs}$ shape factor; $F_{qd}$ depth factor; $F_{qi}$ inclination factor
     
22.  Soil weight term
     
     $$
     \tfrac{1}{2} \gamma B' N_\gamma F_{\gamma s} F_{\gamma d} F_{\gamma i}
     $$
     
     where $\gamma$ effective unit weight below the base (kN/m³); $B'$ effective width (m); $N_\gamma$ bearing capacity factor; $F_{\gamma s}$ shape factor; $F_{\gamma d}$ depth factor; $F_{\gamma i}$ inclination factor
     
23.  Ultimate bearing capacity
     
     Meyerhof's general equation (1963), Das & Sivakugan, Eq. 6.28
     
     $$
     q_n = c' N_c F_{cs} F_{cd} F_{ci} + q N_q F_{qs} F_{qd} F_{qi} + \tfrac{1}{2} \gamma B' N_\gamma F_{\gamma s} F_{\gamma d} F_{\gamma i}
     $$
     
     where $T_1$ cohesion term (kPa); $T_2$ surcharge term (kPa); $T_3$ soil weight term (kPa)
     
24.  Net ultimate bearing capacity
     
     $$
     q_{n(net)} = q_n - q
     $$
     
     where $q_n$ ultimate bearing capacity (kPa); $q$ overburden at the base (kPa)
     
25.  Maximum contact pressure
     
     $$
     q_{max} = \frac{V}{A} \left(1 + \frac{6 e_B}{B} + \frac{6 e_L}{L}\right)
     $$
     
     where $V$ vertical load (kN); $B$ width (m); $e_B$ eccentricity along the width (m); $L$ length (m); $e_L$ eccentricity along the length (m)
     
26.  Minimum contact pressure
     
     $$
     q_{min} = \frac{V}{A} \left(1 - \frac{6 e_B}{B} - \frac{6 e_L}{L}\right)
     $$
     
     where $V$ vertical load (kN); $B$ width (m); $e_B$ eccentricity along the width (m); $L$ length (m); $e_L$ eccentricity along the length (m)
     
27.  Equivalent uniform pressure
     
     Meyerhof
     
     $$
     q_{eq} = \frac{V}{A'}
     $$
     
     where $V$ vertical load (kN); $A'$ effective area (m²)
     
28.  Bearing capacity
     
     On soil, the equivalent uniform pressure (UFS 3-220-20 §4-5.1.4)
     
     $$
     FS = \frac{q_n}{q_{eq}}
     $$
     
29.  Depth factor
     
     Das & Sivakugan, Table 6.3, Hansen (1970)
     
     $$
     F_{qd} = 1 + 2\tan\phi' (1 - \sin\phi')^2 \tan^{-1}\frac{D_f}{B}
     $$
     
     where $D_f/B$ depth over width
     
30.  Maximum contact pressure
     
     $$
     q_{max} = \frac{V}{\pi D^2 / 4}
     $$
     
     where $V$ vertical load (kN); $D$ diameter (m)
     
31.  Minimum contact pressure
     
     $$
     q_{min} = \frac{V}{\pi D^2 / 4}
     $$
     
     where $V$ vertical load (kN); $D$ diameter (m)
     
32.  Depth factor
     
     Das & Sivakugan, Table 6.3, Hansen (1970)
     
     $$
     F_{cd} = 1 + 0.4\,\tan^{-1}\frac{D_f}{B}
     $$
     
     where $D_f/B$ depth over width
     
33.  Depth factor
     
     Das & Sivakugan, Table 6.3, Hansen (1970)
     
     $$
     F_{qd} = 1
     $$
     
     where $D_f/B$ depth over width
     

## 3Sliding

1.  Shear resistance under the base
    
    Cast on cohesionless soil, C = 1.0 (Eq. 10.6.3.4-2); free mode takes it without φτ
    
    $$
    R_\tau = V \tan \phi_f
    $$
    
    where $V$ vertical load (kN)
    
2.  Resistance to sliding
    
    $$
    R = R_\tau
    $$
    
    where $R_\tau$ shear resistance under the base (kN)
    
3.  Sliding
    
    $$
    FS = \frac{R}{H}
    $$
    

## 4Eccentricity

1.  Eccentricity along the width
    
    $$
    e_B \le \frac{B}{6}
    $$
    
2.  Eccentricity along the length
    
    $$
    e_L \le \frac{L}{6}
    $$
    

## 5Stress increase below the base

1.  Net pressure at the base
    
    $$
    q_0 = \frac{V}{A} - q
    $$
    
    where $V$ vertical load (kN); $q$ overburden at the base (kPa)
    
2.  Average stress increase in each stratum
    
    Boussinesq (AASHTO Fig. 10.6.2.4.1-1)
    
    $$
    \Delta\sigma'_{av} = \frac{1}{z_b - z_t}\int_{z_t}^{z_b} \Delta\sigma \, dz
    $$
    
    where $q_0$ net pressure at the base (kPa)
    

## 6Consolidation

1.  Thickness below the base, each stratum
    
    The stratum's thickness below the base
    
    $$
    H_c
    $$
    
2.  Effective stress at the stratum's middle, each stratum
    
    σ′vo at the middle of the whole stratum, in the ground before the load
    
    $$
    \sigma'_{vo}(z_m)
    $$
    
3.  Overconsolidation ratio, the same in each layer, each stratum
    
    The stratum's σ′c over σ′vo at its middle, in the ground: the same in each of its layers, as FHWA-NHI-16-064's D.39 takes its clays' (Table D-117)
    
    $$
    OCR = \frac{\sigma'_c}{\sigma'_{vo}(z_m)}
    $$
    
    where $\sigma'_{vo}(z_m)$ effective stress at the stratum's middle, each stratum (kPa)
    
4.  Thickness of each layer of a clay
    
    The stratum's part below the base in equal layers of at most $3048\,\text{mm}$, the thicker end of AASHTO C10.6.2.4.3's increments, as FHWA's examples take a footing's
    
    $$
    H_i
    $$
    
    where $H_c$ thickness below the base, each stratum (m)
    
5.  Effective stress at the middle of each layer
    
    $z_m$, the middle of the layer (AASHTO 10.6.2.4.3)
    
    $$
    \sigma'_o = \sigma'_v(z_m)
    $$
    
6.  Average stress increase over each layer
    
    Boussinesq (AASHTO Fig. 10.6.2.4.1-1), averaged over the layer
    
    $$
    \Delta\sigma'_{av} = \frac{1}{z_b - z_t}\int_{z_t}^{z_b} \Delta\sigma \, dz
    $$
    
    where $q_0$ net pressure at the base (kPa)
    
7.  Preconsolidation pressure at the middle of each layer
    
    At its middle, the stratum's OCR times its σ′o (FHWA-NHI-16-064, D.39, Table D-117; AASHTO 10.6.2.4.3: σ′p at the layer's midpoint)
    
    $$
    \sigma'_p = OCR\,\sigma'_o
    $$
    
    where $OCR$ overconsolidation ratio, the same in each layer, each stratum; $\sigma'_o$ effective stress at the middle of each layer (kPa)
    
8.  Primary settlement of each layer
    
    Overconsolidated: $\sigma'_o<\sigma'_p<\sigma'_o+\Delta\sigma'_{av}$
    
    $$
    S_{c,i} = \frac{C_s H_i}{1 + e_o} \log \frac{\sigma'_p}{\sigma'_o} + \frac{C_c H_i}{1 + e_o} \log \frac{\sigma'_o + \Delta\sigma'_{av}}{\sigma'_p}
    $$
    
    where $H_i$ thickness of each layer of a clay (m); $\sigma'_o$ effective stress at the middle of each layer (kPa); $\Delta\sigma'_{av}$ average stress increase over each layer (kPa); $\sigma'_p$ preconsolidation pressure at the middle of each layer (kPa)
    
9.  Primary settlement of each layer
    
    Overconsolidated: $\sigma'_o+\Delta\sigma'_{av}\le\sigma'_p$
    
    $$
    S_{c,i} = \frac{C_s H_i}{1 + e_o} \log \frac{\sigma'_o + \Delta\sigma'_{av}}{\sigma'_o}
    $$
    
    where $H_i$ thickness of each layer of a clay (m); $\sigma'_o$ effective stress at the middle of each layer (kPa); $\Delta\sigma'_{av}$ average stress increase over each layer (kPa); $\sigma'_p$ preconsolidation pressure at the middle of each layer (kPa)
    
10.  Primary settlement, its layers' sum, each stratum
     
     Its layers', each settled on its own (AASHTO C10.6.2.4.3: "The total value of Sc is the summation of Sc for each increment")
     
     $$
     S_{c(p)} = \Sigma S_{c,i}
     $$
     
     where $S_{c,1}$ primary settlement of each layer (m)
     

## 7Settlement

1.  Average soil modulus
    
    $$
    E_s = \Sigma E_i h_i / \Sigma h_i
    $$
    
2.  Average Poisson's ratio
    
    $$
    \mu_s = \Sigma \mu_i h_i / \Sigma h_i
    $$
    
3.  Length to width, a quarter of the base
    
    $$
    m' = L / B
    $$
    
4.  Steinbrenner's factor
    
    No rigid layer below: Schleicher's, I₂ = 0 (Das & Sivakugan, Eqs. 9.20 and 9.21)
    
    $$
    I_1(m', n' = \infty)
    $$
    
    where $m'$ length to width, a quarter of the base
    
5.  Steinbrenner's factor
    
    No rigid layer below: Schleicher's, I₂ = 0 (Das & Sivakugan, Eqs. 9.20 and 9.21)
    
    $$
    I_2(m', n' = \infty)
    $$
    
    where $m'$ length to width, a quarter of the base
    
6.  Shape factor
    
    $$
    I_s = I_1 + \frac{1 - 2\mu_s}{1 - \mu_s} I_2
    $$
    
    where $I_1$ Steinbrenner's factor; $I_2$ Steinbrenner's factor; $\mu_s$ average Poisson's ratio
    
7.  Elastic settlement
    
    $$
    S_e = q_0 (\alpha B') \frac{1 - \mu_s^2}{E_s} I_s I_f
    $$
    
    where $q_0$ net pressure at the base (kPa); $E_s$ average soil modulus (kPa); $\mu_s$ average Poisson's ratio; $I_s$ shape factor; $I_f$ depth factor
    
8.  Primary consolidation settlement
    
    $$
    S_{c(p)} = \Sigma S_{c(p),i}
    $$
    
    where $S_{c(p),i}$ primary settlement, its layers' sum, each stratum (m)
    
9.  Total settlement
    
    $$
    S = S_e + S_{c(p)}
    $$
    
    where $S_e$ elastic settlement (m); $S_{c(p)}$ primary consolidation settlement (m)
    
10.  Settlement
     
     $$
     S \le 25\,\text{mm}
     $$
     
11.  Total settlement
     
     $$
     S = S_e
     $$
     
     where $S_e$ elastic settlement (m)
     

## 8Allowable bearing pressure

1.  Maximum contact pressure
    
    $$
    q_{max} = \frac{V}{A} \left(1 + \frac{6 e_B}{B} + \frac{6 e_L}{L}\right)
    $$
    
    where $V$ vertical load (kN); $B$ width (m); $e_B$ eccentricity along the width (m); $L$ length (m); $e_L$ eccentricity along the length (m)
    
2.  Allowable bearing pressure
    
    Given with the base
    
    $$
    q_a
    $$
    
3.  Bearing pressure
    
    The greatest ordinate of the base's linear pressure diagram, at its most loaded edge (its formula as UFC 3-220-20 prints it, Eq. 5-7): the total pressure at the base
    
    $$
    q_{max} \le q_a
    $$

---

Source: https://rischio.io/docs/shallow-foundation/equations/
