# The calculation report

Rischio's calculation report: what it contains, how to print it, save it as PDF or export it to Word, add your letterhead and record its sign-off.

Each calculated model has its calculation report, the document you hand in. It follows the order in which a reviewer checks a calculation: what it checks, what comes out, on what basis, the model, then every step.

## Open it

In the editor, **Report**; on the Models page, **Calculation report**, in the model’s menu. Both once the model is calculated and its results are up to date. A report whose model changed since says so, with **Calculate**: it calculates the model and comes back to the report.

![The calculation report of a cantilever wall: its outline of sections beside it, its title block with the calculation number, its scope and the summary of its three checks](https://rischio.io/_astro/report-dark.D2XetMm7_Z1TIpva.webp)![The calculation report of a cantilever wall: its outline of sections beside it, its title block with the calculation number, its scope and the summary of its three checks](https://rischio.io/_astro/report-dark.D2XetMm7_Z1TIpva.webp)

## What’s in it

1.  A title block with your letterhead or Rischio’s, the model, the analysis, the calculation number (the model and how many times it was calculated, such as 14924-3, also at the foot of every page), the date and the units the model reads in ([SI or US customary](https://rischio.io/docs/studio/editor/#units), such as kN, m, kPa or kip, ft, ksf).
2.  **Scope**: the checks this calculation makes.
3.  **Summary**: each check with its value, its limit, its margin and its result, OK or NOT OK. The margin is how much of its limit the check has left, read the same way in every check: a sliding CDR of 2.05 against 1.00 keeps 51 %, an eccentricity of 0.11 m against 0.93 m keeps 88 %, and the lowest margin governs; under a design code, its limit state too (Strength I, Service I, Extreme Event I). A cover to a cantilever’s bars at AASHTO’s least, its default, keeps 0 % and passes: a rule of detailing never governs, and one that fails fails the model. A check without a limit shows its value alone.
4.  **Design basis**: the design code, or free mode with the designer’s limits. Under a code, the load combinations that govern with their load factors γ, and each check’s resistance factor φ with its source. Then every limit with its source, and each method the calculation used, with who chose it and why.
5.  **Model**: the drawing of the section (for piles, also the head close up with its loads), and the data, group by group. [Your notes on the drawing](https://rischio.io/docs/studio/results/#your-notes-on-the-drawing) print only if you ask, since they’re often your own: under the figure, **Print them** numbers them on it with their words below, and **Leave them out** takes them away. Each load is a table with a column per load type (DC, LL, EQ…). **Where the values come from** says that each one is yours, as typed, and lists what the calculation took where the model leaves a value empty, such as a pile’s modulus.
6.  Under a design code, **Loads by type, unfactored**: each load type’s force and moment, such as the wall’s weight DC, the soil over the heel EV and the backfill’s thrust EH, each from the step that computes it.
7.  The calculation: one section per check, in the order of the FHWA worked example the tool follows, with its figures and each equation worked out by the methods the model uses. Under a code, each check reads from the combination that governs it down to the loads by type: a bearing check shows its factored load, its eccentricity, B′ and the bearing factors on that B′. Values with depth are charts side by side, the way LPILE plots a pile’s deflection, moment, shear and soil reaction; a pressure on a wall is drawn on the wall’s back. Under a code, an MSE wall’s section of its layers opens with a table of every layer: its factored tension and pullout load, its factored rupture and pullout resistances, and each resistance over its load. The references the **Results** tab shows beside them stay out of the report.
8.  The structural design, where the model has a structure: its chapters after the geotechnics’, numbered as theirs. The forces along each part of a cantilever wall, or down the pile, come first, their diagrams under each limit state (Strength I and Service I, and Extreme Event I with an earthquake) and their largest values, unfactored in free mode. Under a design code, **Reinforcement** follows, each part’s bars in a table with their cross-sections, then a chapter for each part (**Stem**, **Toe**, **Heel**, or the **Pile**), with its checks and rules in sections of their own, strength first ([Structural design](https://rischio.io/docs/studio/structural-design/)).
9.  **Notes**: the model’s warnings.

The report is always in light colors, whatever the studio’s theme.

## Edit it

Beside the report, its sections are listed in the order they print, numbered as they print: click one to go to it. The bar with **Edit report**, **Export to Word** and **Print or save as PDF** stays at the top as you scroll.

**Edit report** opens its sections beside the paper, numbered as they print. Drag a section to its place, turn one off or on, and add your own texts, such as a project description or your conclusions, here or between two sections in the report; click a section to go to it. A text holds your words; none of the calculation’s numbers is computed in it. The scope, the summary, the design basis and the model stay where they are, locked, since a reviewer looks for them there. Your changes are saved with the model and its copies, and **Done** shows the report as it prints.

A text of yours also edits where you read it: it shows **Edit** at its corner, and a click on it opens its title and its words right there. **Done**, or Esc, closes it.

## Print it, save it as PDF, export it to Word

**Print or save as PDF** opens the browser’s print dialog, where “Save as PDF” makes the file. **Export to Word** downloads a `.docx` to edit or to bring into your own report. Each page carries the model’s name, the calculation number and the page number.

| Plan | The report |
| --- | --- |
| Free | A preview, with a watermark |
| Professional, and its trial | Print, PDF and Word |
| Education | Print, PDF and Word, marked “Educational use” |

## Your letterhead

With Professional, **Settings › Letterhead** puts your company on the report: a logo (PNG, JPG or WebP, up to 1 MB), its name, and its address and contact.

## Its sign-off

The **Report record** holds the report’s reference and who prepared and reviewed it, each with name, license, signature (drawn or uploaded) and date. **Print it with the report** adds it to the printed copy. The record stays in your browser, not in your account.

---

Source: https://rischio.io/docs/studio/report/
