Rischio
Start free

Gabion Retaining Wall Design with a Worked Example

How a gabion retaining wall works and how it's designed: baskets, stone, the checks of the whole wall and of each level, and a 3 m wall worked step by step.

17 min readLéelo en español
13.3 kPaWall friction · δ′ = 16°SlidingFS 2.38 ≥ 1.5
In this article
  1. What a gabion retaining wall is
  2. Gabion baskets, wire and stone
  3. Gabion wall design: what is checked
  4. Worked example: a 3 m gabion wall on a creek bank
  5. The same wall in Rischio
  6. How a gabion wall is built
  7. Frequently asked questions
  8. References

A gabion retaining wall is a gravity wall built of wire baskets filled with rock, laced together and stacked in levels. It holds the soil with the weight of its stone, like a concrete gravity wall, and it’s designed with the same checks: sliding, overturning and bearing capacity, plus one of its own, each level against the level below it.

This guide covers what a gabion wall is made of, where it fits, how its design works, and a worked example: a 3 m wall on a creek bank, checked by hand and with Rischio’s engine, which gives the same numbers.

What a gabion retaining wall is

FHWA’s manual on earth retaining structures describes gabion walls as rows and tiers of orthogonal wire baskets filled with rock fragments and tied together (FHWA-NHI-07-071, 6.4.1). They are widely used to protect channels and riverbanks, and also as retaining walls, particularly in rugged terrain. Among retaining walls they belong to the modular gravity walls, with crib, bin and precast module walls: prefabricated units whose own weight, and the weight of what fills them, resists the earth pressure.

A gabion wall’s front and back can be vertical or stepped. The usual section is stepped in front, each level set back from the one below it, with a vertical back against the backfill. FHWA notes that walls higher than about 3 m (10 ft) are usually given a batter, leaning back into the soil at 1 in 10, 1 in 6 or 1 in 4, to improve their stability.

Advantages and limitations

What a gabion wall offers, by FHWA’s account (6.1, 6.4.1):

  • It drains freely. If the backfill doesn’t trap water, the wall isn’t loaded by water pressure, and since it drains it resists frost.
  • It’s flexible, so it suits compressible ground: gabion walls tolerate differential settlements of the order of 1/50, where most modular walls tolerate about 1/300 (6.6.7).
  • It’s simple to build and needs neither skilled labor nor special equipment, which suits remote sites where baskets are assembled by hand and filled with local stone.
  • It blends into the landscape, especially when built with local rock, and pipes can pass through it.

Its limitations:

  • It takes a lot of labor, up to half of its cost, so it may not pay where labor is expensive.
  • It needs good stone. If the rock isn’t local, the cost can rise until a gabion wall is no longer worth considering.
  • The wire can corrode in aggressive environments, and baskets are easier to damage than concrete.
  • It is built from the bottom up and isn’t suited to deep foundations.

FHWA finds gabion walls are typically not cost-effective above about 7.6 m (25 ft).

Gabion baskets, wire and stone

The baskets

Most gabions are steel wire mesh of two kinds (FHWA-NHI-07-071, 6.4.3):

  • Hexagonal woven mesh, with double-twisted wires and an opening of about 83 × 114 mm (3.25 × 4.5 in). It is supplied folded flat; each basket is erected on site and laced along its edges.
  • Square welded mesh, with an opening of about 76 mm (3 in), hot-dip galvanized after welding. It is stiffer and less flexible than woven mesh.

The wires of woven mesh are 2.0 to 3.8 mm in diameter (0.08 to 0.15 in); for permanent walls, at least 2.5 mm (0.1 in) and galvanized before weaving. In sea water or polluted water, the wire gets a PVC coating 0.4 to 0.6 mm thick. Baskets of nylon, polypropylene or polyethylene don’t corrode, but fire and ultraviolet light attack them, so their exposed faces are covered.

Baskets come in a standard width of about 0.9 m (3 ft), lengths from 0.9 to 3.7 m (3 to 12 ft) and heights of 0.3, 0.45 and 0.9 m (1, 1.5 and 3 ft). Longer baskets are divided into cells by diaphragms of the same mesh, which stiffen them and make them easier to assemble.

The rock fill

The rock should be sound, durable and well graded, between 100 and 250 mm (4 and 10 in), with no piece whose smallest dimension is under 100 mm, and without shale, soil or fines. Its porosity is generally 0.30 to 0.40, and it sets the unit weight of the gabions (FHWA-NHI-07-071, Eq. 6-3):

γg=(1−nr) Gs γw\gamma_g = (1 - n_r)\,G_s\,\gamma_w

with nrn_r the porosity of the rock fill, GsG_s the specific gravity of the rock and γw\gamma_w the unit weight of water. A rock with Gs=2.65G_s = 2.65 packed to nr=0.35n_r = 0.35 gives (1−0.35)×2.65×9.81=16.9(1 - 0.35) \times 2.65 \times 9.81 = 16.9 kN/m³. The weight of the wire is small and is usually left out.

The backfill and the filter

Behind the wall goes an open-graded granular backfill, compacted like that of other gravity walls. A filter, a geotextile or a graded soil, covers the back and the steps of the wall so that the backfill doesn’t wash into the voids of the stone. In a wall that stands partly in water, the backfill has to drain freely, or water pressure builds up behind the wall when the water in front drops.

Gabion wall design: what is checked

A gabion wall is checked whole, like any gravity wall, and level by level.

W1W2W3PaPa,hPa,vPwUOForces · kN/mW1 = 51.08W2 = 34.00W3 = 25.50Pa,h = 21.21Pa,v = 6.08Pw = 4.91U = 24.53
The forces on the worked example's wall, in kN per metre of wall.

The loads

  • The weight of each level, its area times the unit weight of the gabions. Below the water, the voids fill with water and a gabion weighs γg+nγw\gamma_g + n\gamma_w, with the uplift on the base acting separately.
  • The active earth pressure of the backfill. AASHTO’s commentary applies Coulomb’s theory to modular walls (C3.11.5.3), with the thrust acting on the back of the wall. Where the back is stepped, the thrust is taken on the plane from the heel to the back corner of the top level, and the soil between that plane and the baskets counts as part of the wall. The friction between the backfill and the wall, δ′\delta', may be reduced where a geotextile lines the back (FHWA-NHI-07-071, 6.6.9). Rankine and Coulomb covers both theories.
  • Water. With the stone and the backfill draining freely, FHWA designs gabion walls without water pressure. A wall that stands in a river or a creek gets the water’s thrust behind it and the uplift under its base.

The checks of the whole wall

  • Sliding of the wall on its base: the friction of the base on the foundation soil against the horizontal forces.
  • Overturning, judged as AASHTO does by the eccentricity of the resultant on the base, ee. Under AASHTO’s factored loads the resultant on soil stays within the middle two-thirds of the base (11.6.3.3); with factors of safety it stays within the middle third, e≤B/6e \le B/6.
  • Bearing capacity of the foundation soil under the base, on its effective width B′=B−2eB' = B - 2e.
  • Global stability of the slope that holds the wall, by limit equilibrium.

With factors of safety, FHWA’s Geotechnical Engineering Circular No. 6 gives 1.5 against sliding (5.4) and 3.0 on bearing (5.2.6), and the middle third for the eccentricity (6.4.1).

Each level on the one below

A gabion wall can also fail through itself: the levels above a joint slide on the level below, or tip over it. FHWA asks that, in a stepped wall, sliding and eccentricity be checked at each change of section, ignoring the resistance of the wire mesh and of the connections between baskets (FHWA-NHI-07-071, 6.6.9). At each joint, the block of levels above it takes its own earth pressure, over its own height, and slides on the friction angle between gabions.

PaPa,h = 9.89 kN/mFS = 4.41 ≥ 1.5e = 0.042 m ≤ 0.333 mLevels 2 and 3 on level 1PaPa,h = 2.47 kN/mFS = 7.42 ≥ 1.5e = 0.011 m ≤ 0.25 mLevel 3 on level 2
Each joint is checked with the levels above it as one block, under the earth pressure over their own height.

Worked example: a 3 m gabion wall on a creek bank

A creek is eating into the bank below a garden, and a 3 m gabion wall will hold the bank with the stream standing against its face. Check the wall with factors of safety: 1.5 against sliding, 3.0 on bearing, and the resultant within the middle third of the base and of each level.

Level 12.50 mLevel 22.00 mLevel 31.50 m3.00 m1.00 m0.50 m0.50 mGabionsγ = 17 kN/m³n = 0.35φ = 35° between levelsBackfillγ = 18.5 kN/m³γsat = 20.5 kN/m³φ' = 32°c' = 0Foundation soilγ = 19.5 kN/m³γsat = 21 kN/m³φ' = 34°c' = 0
  • Three levels 1.00 m high: level 1, at the base, 2.50 m wide; level 2, 2.00 m; level 3, 1.50 m. The steps are in front, 0.50 m each, and the back is vertical, so the base is BB = 2.50 m.
  • The base is 0.50 m below the ground in front.
  • Gabions: γg\gamma_g = 17 kN/m³, porosity nn = 0.35, friction angle between levels 35°.
  • Backfill, a silty sand: γ\gamma = 18.5 kN/m³, γsat\gamma_{sat} = 20.5 kN/m³, ϕ′\phi' = 32°, c′c' = 0, level.
  • Foundation, alluvial sand and gravel: γ\gamma = 19.5 kN/m³, γsat\gamma_{sat} = 21 kN/m³, ϕ′\phi' = 34°, c′c' = 0.
  • Water: the creek stands 0.50 m deep against the face, 1.00 m above the base, and the water behind the wall is at the same level, 2.00 m below the crest.
  • γw\gamma_w = 9.81 kN/m³. Moments are taken about the toe, O.

Step 1: the weight of each level

Level 1 is under water, its voids full, so it weighs γg+nγw=17+0.35×9.81=20.43\gamma_g + n\gamma_w = 17 + 0.35 \times 9.81 = 20.43 kN/m³. Levels 2 and 3 are above the water.

LevelWidth (m)Area (m²/m)Unit weight (kN/m³)WW (kN/m)Arm from O (m)
12.502.5020.4351.081.25
22.002.0017.0034.001.50
31.501.5017.0025.501.75

Each arm is the distance from the toe to the middle of the level: level 2, for instance, runs from 0.50 to 2.50 m, so its middle is at 1.50 m.

Step 2: the earth pressure

The back of the wall is a vertical plane, θ=0\theta = 0, from the heel to the crest, and no soil rests on the baskets inside it. The thrust is Coulomb’s on that plane, with a level backfill and a wall friction of half of ϕ′\phi', δ′\delta' = 16°, the most AASHTO gives a modular wall with a continuous back (Table C3.11.5.9-1):

Ka=cos⁡2ϕ′cos⁡δ′[1+sin⁡(ϕ′+δ′)sin⁡ϕ′cos⁡δ′]2=cos⁡232°cos⁡16°[1+sin⁡48° sin⁡32°cos⁡16°]2=0.2782K_a = \frac{\cos^2\phi'}{\cos\delta'\left[1 + \sqrt{\dfrac{\sin(\phi' + \delta')\sin\phi'}{\cos\delta'}}\right]^2} = \frac{\cos^2 32°}{\cos 16°\left[1 + \sqrt{\dfrac{\sin 48°\,\sin 32°}{\cos 16°}}\right]^2} = 0.2782

The vertical effective stress behind the wall is 18.5×2.00=37.0018.5 \times 2.00 = 37.00 kPa at the water, 2.00 m down, and 37.00+(20.5−9.81)×1.00=47.6937.00 + (20.5 - 9.81) \times 1.00 = 47.69 kPa at the base. The thrust is KaK_a times the area of that diagram:

∫0Hσv′ dz=12×37.00×2.00+37.00+47.692×1.00=37.00+42.35=79.35 kN/m\int_0^{H}\sigma'_v\,dz = \tfrac{1}{2} \times 37.00 \times 2.00 + \tfrac{37.00 + 47.69}{2} \times 1.00 = 37.00 + 42.35 = 79.35 \text{ kN/m} Pa=0.2782×79.35=22.07 kN/mP_a = 0.2782 \times 79.35 = 22.07 \text{ kN/m}

It acts at δ′\delta' = 16° from the horizontal, so it pushes the wall with Pa,h=22.07cos⁡16°=21.21P_{a,h} = 22.07\cos 16° = 21.21 kN/m and bears down on its back with Pa,v=22.07sin⁡16°=6.08P_{a,v} = 22.07\sin 16° = 6.08 kN/m. Its height above the base is the centroid of the same diagram:

ya=37.00×1.667+37.00×0.500+5.35×0.33379.35=1.03 my_a = \frac{37.00 \times 1.667 + 37.00 \times 0.500 + 5.35 \times 0.333}{79.35} = 1.03 \text{ m}

taking the triangle above the water, the rectangle below it and the triangle below it, whose area is 12×10.69×1.00=5.35\tfrac{1}{2} \times 10.69 \times 1.00 = 5.35.

Step 3: the water

Behind the wall the water stands 1.00 m above the base:

Pw=12γwhw2=12×9.81×1.002=4.905 kN/mP_w = \tfrac{1}{2}\gamma_w h_w^2 = \tfrac{1}{2} \times 9.81 \times 1.00^2 = 4.905 \text{ kN/m}

at 0.33 m above the base. The creek pushes back on the face, but the check leaves it out, as it leaves out the soil in front of the wall: the safe side. Under the base, the water pushes up with u=9.81×1.00=9.81u = 9.81 \times 1.00 = 9.81 kPa at the heel and at the toe:

U=9.81×2.50=24.525 kN/mU = 9.81 \times 2.50 = 24.525 \text{ kN/m}

at the middle of the base, 1.25 m from the toe.

Step 4: the forces and the eccentricity

ForceVertical (kN/m)Horizontal (kN/m)Arm (m)Moment about O (kN·m/m)
W1W_151.081.2563.855 resisting
W2W_234.001.5051.000 resisting
W3W_325.501.7544.625 resisting
Pa,vP_{a,v}6.082.5015.208 resisting
Pa,hP_{a,h}21.211.0321.911 overturning
PwP_w4.9050.331.635 overturning
UU−24.5251.2530.656 overturning
Total92.1426.12174.69 and 54.20
e=∣B2−ΣMR−ΣMOΣV∣=∣1.25−174.69−54.2092.14∣=0.058 m≤B6=0.417 me = \left|\frac{B}{2} - \frac{\Sigma M_R - \Sigma M_O}{\Sigma V}\right| = \left|1.25 - \frac{174.69 - 54.20}{92.14}\right| = 0.058 \text{ m} \le \frac{B}{6} = 0.417 \text{ m}

The resultant falls 0.058 m behind the middle of the base, well within the middle third. The overturning ratio, ΣMR/ΣMO=3.22\Sigma M_R/\Sigma M_O = 3.22, is only a reference: AASHTO judges overturning by where the resultant falls.

Step 5: sliding

The base slides on the foundation soil. FHWA takes the friction there as the lesser of the infill’s and the foundation soil’s (FHWA-NHI-07-071, 6.6.3), here the soil’s ϕ′\phi' = 34°, and the passive resistance in front of the toe is left out:

FS=ΣVtan⁡ϕ′ΣH=92.14×tan⁡34°26.12=62.1526.12=2.38≥1.5FS = \frac{\Sigma V \tan\phi'}{\Sigma H} = \frac{92.14 \times \tan 34°}{26.12} = \frac{62.15}{26.12} = 2.38 \ge 1.5

Step 6: bearing capacity

The base is a strip footing B′=2.50−2×0.0576=2.385B' = 2.50 - 2 \times 0.0576 = 2.385 m wide, 0.50 m deep, under an inclined load. By AASHTO LRFD’s equation (10.6.3.1.2a), with c′=0c' = 0:

qn=γ Df Nq sq dq iq Cwq+12 γ B′ Nγ sγ iγ Cwγq_n = \gamma\,D_f\,N_q\,s_q\,d_q\,i_q\,C_{wq} + \tfrac{1}{2}\,\gamma\,B'\,N_\gamma\,s_\gamma\,i_\gamma\,C_{w\gamma}
  • For ϕ′\phi' = 34°: Nq=eπtan⁡34°tan⁡2(45°+17°)=29.44N_q = e^{\pi\tan 34°}\tan^2(45° + 17°) = 29.44 and Nγ=2(Nq+1)tan⁡34°=41.06N_\gamma = 2(N_q + 1)\tan 34° = 41.06.
  • A long strip has no shape factors, sq=sγ=1s_q = s_\gamma = 1, and the depth factor is taken as dq=1d_q = 1, without counting the shear strength of the soil above the base.
  • The load leans: H/V=26.12/92.14=0.283H/V = 26.12/92.14 = 0.283. Across a strip, AASHTO’s exponent is n=2n = 2, so iq=(1−0.2835)2=0.5134i_q = (1 - 0.2835)^2 = 0.5134 and iγ=(1−0.2835)3=0.3679i_\gamma = (1 - 0.2835)^3 = 0.3679.
  • The water stands above the ground in front, so Cwq=Cwγ=0.5C_{wq} = C_{w\gamma} = 0.5 (Table 10.6.3.1.2a-2), with the total unit weight γ\gamma = 19.5 kN/m³.
qn=19.5×0.50×29.44×0.5134×0.5+12×19.5×2.385×41.06×0.3679×0.5=73.68+175.62=249.31 kPaq_n = 19.5 \times 0.50 \times 29.44 \times 0.5134 \times 0.5 + \tfrac{1}{2} \times 19.5 \times 2.385 \times 41.06 \times 0.3679 \times 0.5 = 73.68 + 175.62 = 249.31 \text{ kPa}

Against the load spread evenly over B′B', q=92.14/2.385=38.63q = 92.14/2.385 = 38.63 kPa:

FS=249.3138.63=6.45≥3.0FS = \frac{249.31}{38.63} = 6.45 \ge 3.0

Step 7: each level on the one below

Levels 2 and 3 on level 1. The block is 2.00 m high and stands above the water. Its earth pressure is the backfill’s over those 2.00 m: ∫σv′ dz=12×37.00×2.00=37.00\int\sigma'_v\,dz = \tfrac{1}{2} \times 37.00 \times 2.00 = 37.00 kN/m, so Pa=0.2782×37.00=10.29P_a = 0.2782 \times 37.00 = 10.29 kN/m, with Pa,hP_{a,h} = 9.89 kN/m and Pa,vP_{a,v} = 2.84 kN/m, at 0.67 m above the joint.

ΣV=34.00+25.50+2.84=62.34 kN/m,FS=62.34×tan⁡35°9.89=43.659.89=4.41≥1.5\Sigma V = 34.00 + 25.50 + 2.84 = 62.34 \text{ kN/m}, \qquad FS = \frac{62.34 \times \tan 35°}{9.89} = \frac{43.65}{9.89} = 4.41 \ge 1.5

About the toe of level 2, 0.50 m from O, the arms are 1.00 m for level 2, 1.25 m for level 3 and 2.00 m for Pa,vP_{a,v}:

ΣMR=34.00×1.00+25.50×1.25+2.84×2.00=71.55,ΣMO=9.89×0.667=6.60\Sigma M_R = 34.00 \times 1.00 + 25.50 \times 1.25 + 2.84 \times 2.00 = 71.55, \qquad \Sigma M_O = 9.89 \times 0.667 = 6.60 e=∣1.00−71.55−6.6062.34∣=0.042 m≤2.006=0.333 me = \left|1.00 - \frac{71.55 - 6.60}{62.34}\right| = 0.042 \text{ m} \le \frac{2.00}{6} = 0.333 \text{ m}

Level 3 on level 2. The block is 1.00 m high: ∫σv′ dz=12×18.5×1.00=9.25\int\sigma'_v\,dz = \tfrac{1}{2} \times 18.5 \times 1.00 = 9.25 kN/m, Pa=2.573P_a = 2.573 kN/m, with Pa,hP_{a,h} = 2.473 kN/m and Pa,vP_{a,v} = 0.709 kN/m at 0.33 m above the joint.

ΣV=25.50+0.71=26.21 kN/m,FS=26.21×tan⁡35°2.473=18.352.473=7.42≥1.5\Sigma V = 25.50 + 0.71 = 26.21 \text{ kN/m}, \qquad FS = \frac{26.21 \times \tan 35°}{2.473} = \frac{18.35}{2.473} = 7.42 \ge 1.5 e=∣0.75−25.50×0.75+0.709×1.50−2.473×0.33326.21∣=∣0.75−20.19−0.8226.21∣=0.011 m≤1.506=0.25 me = \left|0.75 - \frac{25.50 \times 0.75 + 0.709 \times 1.50 - 2.473 \times 0.333}{26.21}\right| = \left|0.75 - \frac{20.19 - 0.82}{26.21}\right| = 0.011 \text{ m} \le \frac{1.50}{6} = 0.25 \text{ m}

Step 8: the results

CheckValueLimitPasses
Sliding of the wall2.38≥ 1.5yes
Eccentricity of the wall0.058 m≤ 0.417 myes
Bearing capacity6.45≥ 3.0yes
Levels 2 and 3 on level 1: sliding4.41≥ 1.5yes
Levels 2 and 3 on level 1: eccentricity0.042 m≤ 0.333 myes
Level 3 on level 2: sliding7.42≥ 1.5yes
Level 3 on level 2: eccentricity0.011 m≤ 0.25 myes

The wall passes every check. Sliding on the base governs, with the smallest margin: the water takes a fifth of the weight off the base with its uplift, and adds its own thrust to the earth’s.

The same wall in Rischio

This example is the Gabion wall on a creek bank template of Rischio’s retaining wall tool, in free mode, with factors of safety. Rischio’s engine gives the same values as the hand calculation above: KaK_a = 0.2782, Pa,hP_{a,h} = 21.21 kN/m, ΣV\Sigma V = 92.14 kN/m, sliding 2.38, an eccentricity of 0.058 m and a bearing capacity of 249.3 kPa for a factor of safety of 6.45, and, level by level, 4.41 and 0.042 m, 7.42 and 0.011 m.

Try it here: this is the studio’s editor with that wall. Change a level, the backfill or the water and calculate; the engine checks the whole wall and each level on the one below.

How Rischio treats the levels and the weight of gabions under water is in Gabion walls. The checks it shares with every wall, step by step on a cantilever wall, are in retaining wall design.

How a gabion wall is built

FHWA’s sequence (FHWA-NHI-07-071, 6.4.2):

  1. Excavate to the foundation level, with temporary support if the slopes won’t stand. Remove vegetation, organic matter and weak or compressible soil, level the ground and proof-roll it. A gravel bedding or a concrete leveling pad often gives a working surface and sets the line and level of the wall.
  2. Unfold each woven basket, raise its sides and lace its edges, corners first, then its diaphragms.
  3. Set the empty baskets in place, lace them to their neighbors along every edge that touches, and stretch them taut along the line of the wall before filling.
  4. Fill the baskets in layers, a 0.9 m basket in three, placing ties between the front and back faces at the top of the first and second layers so the face doesn’t bulge. Fill neighboring baskets to the same level at each stage, without damaging the wire or its coating.
  5. Level the last layer of stone with the top of the basket, close the lid and tie it to the sides, the ends and the diaphragms.
  6. Cover the back and the steps with the geotextile or soil filter before placing the backfill, and compact it to at least 95% of the maximum dry density of AASHTO T 99, 100% in its top 0.3 m (1 ft).

Frequently asked questions

How high can a gabion retaining wall be?

FHWA gives gabion walls up to about 7.6 m (25 ft) as cost-effective, and typically not above it. Walls higher than about 3 m are usually battered back into the soil to improve their stability.

Do gabion walls need a foundation?

They need no concrete footing, but they need a prepared base: weak and compressible soil removed, the ground leveled and proof-rolled, and often a gravel bedding or a concrete leveling pad. Their bearing capacity is checked like any wall’s.

Do gabion walls need drainage?

The stone drains freely, so FHWA designs gabion walls without water pressure, as long as the backfill doesn’t trap water. A filter, of geotextile or graded soil, goes between the baskets and the backfill so the soil doesn’t wash into the stone, and a wall in a river needs a free-draining backfill.

What size of stone goes in gabions?

Sound, durable, well-graded rock between 100 and 250 mm (4 and 10 in), with no piece under 100 mm in its smallest dimension.

How long does a gabion wall last?

Its weak point is the wire: FHWA notes that its long-term durability may be questionable, particularly in corrosive environments. Permanent walls use galvanized wire at least 2.5 mm in diameter, with a PVC coating in sea water or polluted water, and sound, durable stone.

References

  • AASHTO (2024). LRFD Bridge Design Specifications, 10th edition. Articles 3.11.5.3, 3.11.5.9, 10.6.3 and 11.6.
  • FHWA (2002). Shallow Foundations, Geotechnical Engineering Circular No. 6, FHWA-IF-02-054.
  • FHWA (2008). Earth Retaining Structures, FHWA-NHI-07-071, Chapter 6.